亚洲一区在线曰日韩下载,99亚洲国产精品精华液,亚洲欧洲国产综合aⅴ无码,欧美亚洲日韩国产系列

位置: 網站首頁 材料
牌號 AW1
對應標準 BS 3100-1991
一般工程用鑄鋼件
Specification for Steel castings for general engineering purposes
歸類 鑄鋼
標簽 滲碳碳鋼鑄鋼
AW1 化學元素成分含量(%)
成分 C Si Mn P S Cr ② Ni ② Cu ② Mo ② 其他合計
最小值 0.1 - 0.6 - - - - - - -
最大值 0.18 0.6 1 0.05 0.05 0.3 0.4 0.3 0.15 0.8
其他單個或其他合計化學成分包括表中未指定值的化學成分。只有在假定存在或在常規分析中肢箕，且有跡象表明其成分將超過規定值的情況下宴宠，才應進行分析。
①碳含量每降低0.01%休惰，最大錳含量則增加0.04%鬓灼，允許最大錳含量到1.1%
②殘余元素朦阶。
AW1 機械性能
熱處理或狀態
抗拉強度
σb
Mpa 		斷后伸長率或延伸率
δ
% 		沖擊吸收能量
KV2
J
As cast ≥460 ≥12 ≥25
A=for anneal by heating to a temperature above the AC3 and cool in the furnace
N=for normalize by heating to a temperature above the AC3 and cool in still air
OQ=for quench into oil from a temperature above the AC3
WQ=for quench into water from a temperature above the AC3
AH=for air harden by heating to a temperature above the AC3 and cool in air at a rate fast enough to produce a hardened microstructure
T=for temper by heating to a temperature below AC1
ST=for solution treat by heating to temperature high enough to dissolve and any intermetallic phases followed by a rapid cool.
For steel AW1, test pieces are blank carburized for 8h at 880°C to 930°C, refined at 870°C to 920°C, cooled in air, oil or water then WQ from 760°C to 760°C
注：數據僅供參考！如有疑問瘪吭，請?zhí)顚?我要糾錯"杰翰！
© 2024 材數庫
版權說明：
⑴ 本網站的所有內容（包括但不限于文字、圖片经芋、音頻焰诲、視頻等）均受到版權保護，版權歸本網站所有旗扑；
⑵ 未經授權蹦骑，禁止以任何形式轉載、復制臀防、傳播或用于其他商業用途眠菇；
⑶ 如需使用本網站內容，請?zhí)崆矮@得授權袱衷。