亚洲一区在线曰日韩下载,99亚洲国产精品精华液,亚洲欧洲国产综合aⅴ无码,欧美亚洲日韩国产系列

位置: 網站首頁 材料
牌號 X2CrNiMoN18-12-4
1.4434
對應標準 NF EN 10028-7-2008
壓力容器用不銹鋼扁平產品
Flat products made of steels for pressure purposes - Part 7 : stainless steels
歸類 奧氏體不銹鋼
標簽 特殊等級
X2CrNiMoN18-12-4 化學元素成分含量(%)
成分 C Si Mn P S Cr Ni Mo N
最小值 - - - - - 16.5 10.5 3 0.1
最大值 0.03 1 2 0.045 0.015 19.5 14 4 0.2
◎ 未經買方同意钙阐，不得隨意向鋼中添加表中未列的元素狞谱，冶煉精加工除外。采取一切必要措施以防在廢鋼和生產原料中帶入這些元素云茸，因?yàn)槠鋾?huì)削弱鋼的機械性能，降低鋼的適用性谤饭。
X2CrNiMoN18-12-4 機械性能
條件 熱處理或狀態
抗拉強度
σb
Mpa 		屈服點
σs
Mpa 		斷后伸長率或延伸率
δ
% 		沖擊吸收能量
KV2
J
C：T ≤ 8 +AT 570~770 Rp0.2：≥290
Rp1.0：≥320
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 35
②③		 20℃：
(l: ≥100么鹊；t: ≥60)
-196℃：
(t: ≥60)
H：T ≤ 13.5 +AT 570~770 Rp0.2：≥270
Rp1.0：≥310
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 35
②③		 20℃：
(l: ≥100；t: ≥60)
-196℃：
(t: ≥60)
P：T ≤ 75 +AT 540~740 Rp0.2：≥270
Rp1.0：≥310
①②		 T ＜ 3mm: ≥40
T ≥ 3mm: ≥ 40
②③		 20℃：
(l: ≥100诚悍；t: ≥60)
-196℃：
(t: ≥60)
◎C- 冷軋帶鋼; H- 熱軋帶鋼; P- 熱軋中厚板勇震；T- 厚度；t- 橫向毛师；l-縱向尼摩。
◎+A=軟化退火；+AT=固溶退火族江；+QT=淬火及回火惜荐；+RA=再結晶退火。
◎ 奧氏體鋼有足夠的韌性避晾，不需要進行沖擊試驗悼晨。相比之下，奧氏體-鐵素體鋼必須按要求做沖擊試驗啥匀，以確保足夠的韌性蛙梆。
*抗晶間腐蝕根據EN ISO 3651-2進行測試。在交貨條件下：有催首；在致敏狀態下：有扶踊。
① 對于連續熱軋產品，可在詢價和訂購時商定Rp0.2(即表中σs)的最小值提高20MPa郎任，Rp1.0的最小值提高10MPa秧耗。
② 如果在軋制寬度<300mm的帶材情況下，采用縱向試驗件舶治，最小值減小如下:屈服強度-15MPa分井，恒定標距的延伸率-5%，比例標距延伸率-2%霉猛。
③ T＜3mm：該值適用于標距為80mm尺锚、寬度為20mm的試件珠闰，也可以使用標距為50mm、寬度為12.5mm的試件瘫辩。T ≥3mm：該值適用于標距為5.65√S的試件伏嗜。

  • 高溫下的最小屈服強度

    Material designationHeat treatment
    condition    		Minimum 0.2% proof strength Rp0.2,MPa
    at a temperature (in°C) of:
    Name Number50①100150200250300350400450500550600
    X2CrNiMoN18-12-4 1.4434+AT248211185167155145140135131129127-
    Minimum 1.0% proof strength Rp1.0,MPa
    at a temperature (in°C) of:
    50①100150200250300350400450500550600
    286246218198183175169164160158157-
    ① Determined by linear interpolation.

  • 高溫下的最小抗拉強度

    Material designationMinimum tensile strength Rm,MPa
    at a temperature (in°C) of:
    Name Number50①100150200250300350400450500550600
    X2CrNiMoN18-12-41.4434525500470440430420415415415410390-
    ① Determined by linear interpolation.

  • 熱處理指南

    Material designationHot formingHeat
    treatment
    symbol    		 Solution anneailing
    ①②    		Post weld heat 
    treatment
    steels with ≤ 0.03% C
    Name NumberTemperature
    ℃    		Type of
    cooling    		Temperature
    ℃ ③④    		Type of
    cooling    		Temperature
    ℃ ⑥    		Type of
    cooling
    X2CrNiMoN18-12-41.44341150 to 850air+AT1070 to 1150water,air ⑤960 to 1040 ⑦forced air 
    ◎ a=air; o=oil; w=water.
    ◎ Scale and annealing colours produced during hot forming, heat treatment or welding may adversely affect the corrosion resistance. They should be removed as far as possible before use, e.g. by pickling.
    ◎ The temperatures of annealing should be agreed for simulated heat treated test pieces.
    ① The solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained and provided these requirements are met even after appropriate subsequent solution annealing.
    ② Re-crystallizing annealing.
    ③ If heat treatment is carried out in a continuous furnace, the upper part of the range specified is usually preferred, or even exceeded.
    ④ The lower end of the range specified for solution annealing should be aimed at for heat treatment as part of further processing,because otherwise the mechanical properties might be affected. If the temperature of hot forming does not drop below the lower temperature for solution annealing.a temperature of 980℃ is adequate as a lower limit for Mo-free steels,a temperature of 1000℃ for steels with Mo contents up to 3% and a temperature of 1020℃ for steets with Mo contents exceeding 3%.
    ⑤ cooling sufficiently rapid.

    ⑥ Minimum holding time:30min.

    ⑦ Not recommended if welded with stabilized filler medal.

近似對照表 奧氏體不銹鋼
中國 中國臺灣 日本 韓國 美國 國際標準組織 德國 法國 歐標
GB ISC CNS JIS KS ASTM UNS ISO DIN EN/DIN W-Nr. NF EN/NF EN 數字牌號
022Cr19Ni13Mo4N S31753 317LN SUS 317LN STS 317LN 317LN S31753 X2CrNiMoN 18-12-4 X2CrNiMoN 18-12-4 1.4434 X2CrNiMoN 18-12-4 X2CrNiMoN 18-12-4 1.4434
X2CrNiMoN18-12-4 對應不同標準
1 EN 10088-1-2005 不銹鋼 第1部分:不銹鋼的清單
2 ISO TS 15510-2003 技術規范 不銹鋼-化學成分
3 ISO 15510-2014 技術規范 不銹鋼-化學成分
4 ISO 9328-7-2018 不銹鋼承壓扁鋼制品
5 NF EN 10088-2-2005 普通用途不銹鋼板和鋼帶的交貨技術條件
6 NF EN 10088-1-2005 不銹鋼 - 第1部分：不銹鋼清單
7 NF EN 10028-7-2008 壓力容器用不銹鋼扁平產品
8 NF EN 10028-7-2000 壓力容器用不銹鋼扁平產品
注：數據僅供參考！如有疑問伐厌，請?zhí)顚?我要糾錯"承绸！
© 2024 材數庫
版權說明：
⑴ 本網站的所有內容（包括但不限于文字、圖片邑丰、音頻伸危、視頻等）均受到版權保護，版權歸本網站所有综界；
⑵ 未經授權瞎角，禁止以任何形式轉載、復制贴祷、傳播或用于其他商業用途；
⑶ 如需使用本網站內容攒筛，請?zhí)崆矮@得授權胎汁。