亚洲一区在线曰日韩下载,99亚洲国产精品精华液,亚洲欧洲国产综合aⅴ无码,欧美亚洲日韩国产系列

位置: 網站首頁 材料
牌號 X2CrNiN18-7
1.4318
對應標準 NF EN 10028-7-2000
壓力容器用不銹鋼扁平產品
Flat products made of steels for pressure purposes Part 7: Stainless steels
歸類 奧氏體不銹鋼
標簽 標準等級
X2CrNiN18-7 化學元素成分含量(%)
成分 C Si Mn P S Cr Ni N
最小值 - - - - - 16.5 6 0.1
最大值 0.03 1 2 0.045 0.015 18.5 8 0.2
◎ 未經買方同意，不得隨意向鋼中添加表中未列的元素虽惭，冶煉精加工除外。采取一切必要措施以防在廢鋼和生產原料中帶入這些元素桥滨，因?yàn)槠鋾?huì)削弱鋼的機械性能，降低鋼的適用性弛车。
X2CrNiN18-7 機械性能
條件 熱處理或狀態
抗拉強度
σb
Mpa 		屈服點
σs
Mpa 		斷后伸長率或延伸率
δ
% 		沖擊吸收能量
KV2
J
C：T ≤ 6 +AT 650~850 Rp0.2：≥350
Rp1.0：≥380
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 40
②③		 20℃：
(l: ≥90齐媒；t: ≥60)
H：T ≤ 12 +AT 650~850 Rp0.2：≥330
Rp1.0：≥370
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 40
②③		 20℃：
(l: ≥90；t: ≥60)
P：T ≤ 75 +AT 650~850 Rp0.2：≥330
Rp1.0：≥370
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 40
②③		 20℃：
(l: ≥90纷跛；t: ≥60)
◎C- 冷軋帶鋼; H- 熱軋帶鋼; P- 熱軋中厚板里初；T- 厚度；t- 橫向忽舟；l-縱向。
◎+A=軟化退火淮阐；+AT=固溶退火叮阅；+QT=淬火及回火；+RA=再結晶退火。
◎ 如果熱加工和隨后冷卻的條件符合ENISO3651-2中對產品機械性能和抗晶間腐蝕性的要求浩姥，則可以省略固溶處理凡宅。
*抗晶間腐蝕根據EN ISO 3651-2進行測試。在交貨條件下：有簸眼；在致敏狀態下：有钓闲。
① 對于連續熱軋產品，可在詢價和訂購時商定Rp0.2(即表中σs)的最小值提高20MPa疤削，Rp1.0的最小值提高10MPa拉盘。
② 如果在軋制寬度<300mm的帶材情況下，采用縱向試驗件撬彭，最小值減小如下:屈服強度-15MPa当糯，恒定標距的延伸率-5%，比例標距延伸率-2%据钱。
③ T＜3mm：該值適用于標距為80mm捧练、寬度為20mm的試件，也可以使用標距為50mm箭谴、寬度為12.5mm的試件风居。T ≥3mm：該值適用于標距為5.65√S的試件。

  • 高溫下的最小屈服強度

    Material designationHeat treatment
    condition    		Minimum 0.2% proof strength Rp0.2,MPa
    at a temperature (in°C) of:
    Name Number100150200250300350400450500550600
    X2CrNiN18-71.4318+AT265200185180170165-----
    Minimum 1.0% proof strength Rp1.0,MPa
    at a temperature (in°C) of:
    100150200250300350400450500550600
    300235215210200195-----
    ① Determined by linear interpolation.

  • 高溫下的最小抗拉強度

    Material designationMinimum tensile strength Rm,MPa
    at a temperature (in°C) of:
    Name Number100150200250300350400450500550600
    X2CrNiN18-71.4318530490460450440430-----

  • 熱處理指南

    Material designationHot formingHeat
    treatment
    symbol    		 Solution anneailing
    ①②    		Post weld heat 
    treatment
    Steel with ≤ 0.03% C
    Name NumberTemperature
    ℃    		Type of
    cooling    		Temperature
    ℃ ③④    		Type of
    cooling    		Temperature
    ℃ ⑥    		Type of
    cooling
    X2CrNiN18-71.43181150 to 850air+AT1020 to 1100water,air ⑤900 to 940air 
    ◎ a=air; o=oil; w=water.
    ◎ Scale and annealing colours produced during hot forming, heat treatment or welding may adversely affect the corrosion resistance. They should be removed as far as possible before use, e.g. by pickling.
    ◎ The temperatures of annealing should be agreed for simulated heat treated test pieces.
    ① The solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained and provided these requirements are met even after appropriate subsequent solution annealing.
    ② Re-crystallizing annealing.
    ③ If heat treatment is carried out in a continuous furnace, the upper part of the range specified is usually preferred, or even exceeded.
    ④ The lower end of the range specified for solution annealing should be aimed at for heat treatment as part of further processing,because otherwise the mechanical properties might be affected. If the temperature of hot forming does not drop below the lower temperature for solution annealing.a temperature of 980℃ is adequate as a lower limit for Mo-free steels,a temperature of 1000℃ for steels with Mo contents up to 3% and a temperature of 1020℃ for steets with Mo contents exceeding 3%.
    ⑤ cooling sufficiently rapid.
    ⑥ Minimum holding time:30min.


X2CrNiN18-7 對應不同標準
1 EN 10088-1-2005 不銹鋼 第1部分:不銹鋼的清單
2 EN 10296-2-2005 機械工程和一般工程用焊接圓鋼管.交貨技術條件.第2部分:不銹鋼
3 ISO TS 15510-2003 技術規范 不銹鋼-化學成分
4 ISO 15510-2014 技術規范 不銹鋼-化學成分
5 ISO 9328-7-2018 不銹鋼承壓扁鋼制品
6 NF EN 10088-2-2005 普通用途不銹鋼板和鋼帶的交貨技術條件
7 NF EN 10088-1-2005 不銹鋼 - 第1部分：不銹鋼清單
8 NF EN 10028-7-2008 壓力容器用不銹鋼扁平產品
9 NF EN 10296-2-2005 機械和一般工程用焊接圓鋼管-交貨技術條件-第2部分:不銹鋼管
10 NF EN 10028-7-2000 壓力容器用不銹鋼扁平產品
注：數據僅供參考掸掸！如有疑問，請?zhí)顚?我要糾錯"蹭秋！
© 2024 材數庫
版權說明：
⑴ 本網站的所有內容（包括但不限于文字、圖片仁讨、音頻、視頻等）均受到版權保護洞豁，版權歸本網站所有盐固；
⑵ 未經授權，禁止以任何形式轉載掐抢、復制候榨、傳播或用于其他商業用途；
⑶ 如需使用本網站內容，請?zhí)崆矮@得授權琅芍。