亚洲一区在线曰日韩下载,99亚洲国产精品精华液,亚洲欧洲国产综合aⅴ无码,欧美亚洲日韩国产系列

位置: 網站首頁 材料
牌號 X3CrNiMoBN17-13-3
1.4910
對應標準 NF EN 10028-7-2000
壓力容器用不銹鋼扁平產品
Flat products made of steels for pressure purposes Part 7: Stainless steels
歸類 奧氏體不銹鋼
標簽 標準等級
密度 8 g/cm3
X3CrNiMoBN17-13-3 化學元素成分含量(%)
成分 C Si Mn P S Cr Ni Mo N B
最小值 - - - - - 16 12 2 0.1 0.0015
最大值 0.04 0.75 2 0.035 0.015 18 14 3 0.18 0.005
◎ 未經買方同意，不得隨意向鋼中添加表中未列的元素，冶煉精加工除外。采取一切必要措施以防在廢鋼和生產原料中帶入這些元素拨才，因為其會削弱鋼的機械性能，降低鋼的適用性旧败。
X3CrNiMoBN17-13-3 機械性能
條件 熱處理或狀態
抗拉強度
σb
Mpa 		屈服點
σs
Mpa 		斷后伸長率或延伸率
δ
% 		沖擊吸收能量
KV2
J
C：T ≤ 6 +AT 580~780 Rp0.2：≥300
Rp1.0：≥330
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 40
②③		 20℃：
(l: ≥100沈贝；t: ≥60)
H：T ≤ 12 +AT 550~750 Rp0.2：≥260
Rp1.0：≥300
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 40
②③		 20℃：
(l: ≥100咳短；t: ≥60)
P：T ≤ 75 +AT 550~750 Rp0.2：≥260
Rp1.0：≥300
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 40
②③		 20℃：
(l: ≥100；t: ≥60)
◎C- 冷軋帶鋼; H- 熱軋帶鋼; P- 熱軋中厚板砰粹；T- 厚度唧躲；t- 橫向；l-縱向敢俭。
◎+A=軟化退火乱孩；+AT=固溶退火；+QT=淬火及回火逃口；+RA=再結晶退火耀即。
◎ 如果熱加工和隨后冷卻的條件符合ENISO3651-2中對產品機械性能和抗晶間腐蝕性的要求，則可以省略固溶處理编苛。
*抗晶間腐蝕根據EN ISO 3651-2進行測試。在交貨條件下：有裤魔；在致敏狀態下：有娜摇。
① 對于連續熱軋產品，可在詢價和訂購時商定Rp0.2(即表中σs)的最小值提高20MPa赖巴，Rp1.0的最小值提高10MPa沿信。
② 如果在軋制寬度<300mm的帶材情況下，采用縱向試驗件猩刁，最小值減小如下:屈服強度-15MPa组漏，恒定標距的延伸率-5%，比例標距延伸率-2%新蟆。
③ T＜3mm：該值適用于標距為80mm觅赊、寬度為20mm的試件，也可以使用標距為50mm琼稻、寬度為12.5mm的試件吮螺。T ≥3mm：該值適用于標距為5.65√S的試件。

  • 高溫下的最小屈服強度

    Material designationHeat treatment
    condition    		Minimum 0.2% proof strength Rp0.2,MPa
    at a temperature (in°C) of:
    Name Number100150200250300350400450500550600
    X3CrNiMoBN17-13-31.4910+AT205187170159148141134130127124121
    Minimum 1.0% proof strength Rp1.0,MPa
    at a temperature (in°C) of:
    100150200250300350400450500550600
    240220200189178171164160157154151

  • 高溫下的最小抗拉強度

    Material designationMinimum tensile strength Rm,MPa
    at a temperature (in°C) of:
    Name Number100150200250300350400450500550600
    X3CrNiMoBN17-13-31.4910495472450440430425420410400385365

  • 熱處理指南

    Material designationHot formingHeat
    treatment
    symbol    		 Solution anneailing
    ①②    		Post weld heat 
    treatment
    Creep resisting steels
    Name NumberTemperature
    ℃    		Type of
    cooling    		Temperature
    ℃ ③④    		Type of
    cooling    		Temperature
    ℃ ⑥    		Type of
    cooling
    X3CrNiMoBN17-13-31.49101150 to 850air+AT1020 to 1100water,air ⑤900 to 950 ⑦air
    ◎ a=air; o=oil; w=water.
    ◎ Scale and annealing colours produced during hot forming, heat treatment or welding may adversely affect the corrosion resistance. They should be removed as far as possible before use, e.g. by pickling.
    ◎ The temperatures of annealing should be agreed for simulated heat treated test pieces.
    ① The solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained and provided these requirements are met even after appropriate subsequent solution annealing.
    ② Re-crystallizing annealing.
    ③ If heat treatment is carried out in a continuous furnace, the upper part of the range specified is usually preferred, or even exceeded.
    ④ The lower end of the range specified for solution annealing should be aimed at for heat treatment as part of further processing,because otherwise the mechanical properties might be affected. If the temperature of hot forming does not drop below the lower temperature for solution annealing.a temperature of 980℃ is adequate as a lower limit for Mo-free steels,a temperature of 1000℃ for steels with Mo contents up to 3% and a temperature of 1020℃ for steets with Mo contents exceeding 3%.

    ⑤ cooling sufficiently rapid.

    ⑥ Minimum holding time:30min.

    ⑦ Recommended for components with greater wall thickness.

  • 物理性能

    Modulus of elasticity atMean coefficient of thermal
    expansion between 20 ℃ and    		Thermal
    conductivity
    at 20℃    		Specific
    thermal
    capacity
    at  20℃    		Specific electrical
    resistivity
    at 20℃
    20°C100°C200°C300°C400°C500°C600°C700°C800°C900°C1000°C100°C200°C300°C400°C500°C600°C700°C800°C900°C1000°C
    KN/mm210-6 K-1W/m.KJ/kg.KΩ.mm2/m
    20019018517517016015514514013512516.316.917.317.818.218.518.7---164500.77

  • 蠕變性能

    DesignationHeat treatment
    condition    		TemperatureStrength for rupture in N/mm2 for ①
    Name Number°C10000h30000h50000h100000h150000h200000h250000h
    X3CrNiMoBN17-13-31.4910+AT550290--220-200-
    560272--202-184-
    570254--186-166-
    580237--170-151-
    590220--155-137-
    600205--141-122-
    610190--127-113-
    620174--114-100-
    630162--102-91-
    640148--92-81-
    650135--83-73-
    660122--75-65-
    670112--68-58-
    680102--61-52-
    69093--56-46-
    70084--52-42-
    71078--48-39-
    72071--45-36-
    73065--41-34-
    74058--37-31-
    75052--34-28-
    76048--31-26-
    77044--28-24-
    78041--25-21-
    79037--22-19-
    80033--20-17-
    ◎ Values were taken from DIN 17460.
    ① Values in parantheses involved time and/or stress extrapolation; values with asterisk involved time extrapolation.


X3CrNiMoBN17-13-3 對應不同標準
1 EN 10088-1-2005 不銹鋼 第1部分:不銹鋼的清單
2 EN 10269-2006 規定高溫和/或低溫性能的緊固件用鋼和鎳合金
3 EN 10302-2008 鎳和鎳鈷合金的耐蠕變鋼
4 EN 10269-2013 規定高溫和/或低溫性能的緊固件用鋼和鎳合金
5 ISO 15510-2014 技術規范 不銹鋼-化學成分
6 NF EN 10269-1999 用于高溫或低溫條件下的緊固件用鋼及鎳合金
7 DIN EN 10269-2014 規定高溫和/或低溫性能的緊固件用鋼和鎳合金
8 ISO 9328-7-2018 不銹鋼承壓扁鋼制品
9 NF EN 10088-1-2005 不銹鋼 - 第1部分：不銹鋼清單
10 NF EN 10028-7-2008 壓力容器用不銹鋼扁平產品
11 NF EN 10028-7-2000 壓力容器用不銹鋼扁平產品
注：數據僅供參考帕翻！如有疑問鸠补，請?zhí)顚?我要糾錯"！
© 2024 材數庫
版權說明：
⑴ 本網站的所有內容（包括但不限于文字嘀掸、圖片紫岩、音頻、視頻等）均受到版權保護睬塌，版權歸本網站所有泉蝌；
⑵ 未經授權，禁止以任何形式轉載衫仑、復制梨与、傳播或用于其他商業用途；
⑶ 如需使用本網站內容，請?zhí)崆矮@得授權枚从。