亚洲一区在线曰日韩下载,99亚洲国产精品精华液,亚洲欧洲国产综合aⅴ无码,欧美亚洲日韩国产系列

位置: 網站首頁 材料
牌號 X2CrNiMo18-15-4
1.4438
對應標準 NF EN 10028-7-2000
壓力容器用不銹鋼扁平產品
Flat products made of steels for pressure purposes Part 7: Stainless steels
歸類 奧氏體不銹鋼
標簽 特殊等級
X2CrNiMo18-15-4 化學元素成分含量(%)
成分 C Si Mn P S Cr Ni Mo N
最小值 - - - - - 17.5 13 3 -
最大值 0.03 1 2 0.045 0.015 19.5 16 4 0.11
◎ 未經買方同意，不得隨意向鋼中添加表中未列的元素次坡，冶煉精加工除外哈涣。采取一切必要措施以防在廢鋼和生產原料中帶入這些元素歹袁，因?yàn)槠鋾?huì)削弱鋼的機械性能山滔，降低鋼的適用性溉跃。
X2CrNiMo18-15-4 機械性能
條件 熱處理或狀態
抗拉強度
σb
Mpa 		屈服點
σs
Mpa 		斷后伸長率或延伸率
δ
% 		沖擊吸收能量
KV2
J
C：T ≤ 6 +AT 550~700 Rp0.2：≥240
Rp1.0：≥270
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 35
②③		 20℃：
(l: ≥100走木；t: ≥60)
-196℃：
(t: ≥60)
H：T ≤ 12 +AT 550~700 Rp0.2：≥220
Rp1.0：≥260
①②		 T ＜ 3mm: ≥35
T ≥ 3mm: ≥ 35
②③		 20℃：
(l: ≥100针榜；t: ≥60)
-196℃：
(t: ≥60)
P：T ≤ 75 +AT 520~720 Rp0.2：≥220
Rp1.0：≥260
①②		 T ＜ 3mm: ≥40
T ≥ 3mm: ≥ 40
②③		 20℃：
(l: ≥100滋冀；t: ≥60)
-196℃：
(t: ≥60)
◎C- 冷軋帶鋼; H- 熱軋帶鋼; P- 熱軋中厚板丙藤；T- 厚度聂歹；t- 橫向；l-縱向插呜。
◎+A=軟化退火乘步；+AT=固溶退火；+QT=淬火及回火砾楞；+RA=再結晶退火榨降。
◎ 如果熱加工和隨后冷卻的條件符合ENISO3651-2中對產品機械性能和抗晶間腐蝕性的要求，則可以省略固溶處理顿豹。
*抗晶間腐蝕根據EN ISO 3651-2進行測試扇牢。在交貨條件下：有；在致敏狀態下：有跋擅。
① 對于連續熱軋產品椰陋，可在詢價和訂購時商定Rp0.2(即表中σs)的最小值提高20MPa，Rp1.0的最小值提高10MPa沪曙。
② 如果在軋制寬度<300mm的帶材情況下奕污，采用縱向試驗件，最小值減小如下:屈服強度-15MPa液走，恒定標距的延伸率-5%碳默，比例標距延伸率-2%。
③ T＜3mm：該值適用于標距為80mm缘眶、寬度為20mm的試件嘱根，也可以使用標距為50mm、寬度為12.5mm的試件巷懈。T ≥3mm：該值適用于標距為5.65√S的試件该抒。

  • 高溫下的最小屈服強度

    Material designationHeat treatment
    condition    		Minimum 0.2% proof strength Rp0.2,MPa
    at a temperature (in°C) of:
    Name Number100150200250300350400450500550600
    X2CrNiMo18-15-41.4438+AT172157147137127120115112110108-
    Minimum 1.0% proof strength Rp1.0,MPa
    at a temperature (in°C) of:
    100150200250300350400450500550600
    206188177167156148144140138136-

  • 高溫下的最小抗拉強度

    Material designationMinimum tensile strength Rm,MPa
    at a temperature (in°C) of:
    Name Number100150200250300350400450500550600
    X2CrNiMo18-15-41.4438430410390385380380-----

  • 熱處理指南

    Material designationHot formingHeat
    treatment
    symbol    		 Solution anneailing
    ①②    		Post weld heat 
    treatment
    steels with ≤ 0.07% C
    Name NumberTemperature
    ℃    		Type of
    cooling    		Temperature
    ℃ ③④    		Type of
    cooling    		Temperature
    ℃ ⑥    		Type of
    cooling
    X2CrNiMo18-15-41.44381150 to 850air+AT1070 to 1150water,air ⑤960 to 1040 ⑦forced air
    ◎ a=air; o=oil; w=water.
    ◎ Scale and annealing colours produced during hot forming, heat treatment or welding may adversely affect the corrosion resistance. They should be removed as far as possible before use, e.g. by pickling.
    ◎ The temperatures of annealing should be agreed for simulated heat treated test pieces.
    ① The solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained and provided these requirements are met even after appropriate subsequent solution annealing.
    ② Re-crystallizing annealing.
    ③ If heat treatment is carried out in a continuous furnace, the upper part of the range specified is usually preferred, or even exceeded.
    ④ The lower end of the range specified for solution annealing should be aimed at for heat treatment as part of further processing,because otherwise the mechanical properties might be affected. If the temperature of hot forming does not drop below the lower temperature for solution annealing.a temperature of 980℃ is adequate as a lower limit for Mo-free steels,a temperature of 1000℃ for steels with Mo contents up to 3% and a temperature of 1020℃ for steets with Mo contents exceeding 3%.
    ⑤ cooling sufficiently rapid.

    ⑥ Minimum holding time:30min.

    ⑦ Not recommended if welded with stabilized filler medal.

X2CrNiMo18-15-4 對應不同標準
1 EN 10088-1-2005 不銹鋼 第1部分:不銹鋼的清單
2 EN 10253-4-2003 對接焊管道接頭.具有特殊檢驗要求的鍛制奧氏體和鐵素體－奧氏體(二相)不銹鋼
3 EN 10088-3-2005 不銹鋼第3部分：一般用途的半成品，鋼棒顶燕，軋制線材和型鋼的交貨條件
4 EN 10088-3-2014 不銹鋼 - 第3部分：半成品凑保，棒材，桿材割岛，線材愉适，型材和光亮產品的一般用途耐腐蝕鋼的交貨技術條件
5 ISO 9328-7-2018 不銹鋼承壓扁鋼制品
6 DIN EN 10088-3-2014 不銹鋼-半成品、棒材咱贪、桿材韩艾、線材、型材及光亮產品交貨技術條件
7 NF EN 10088-2-2005 普通用途不銹鋼板和鋼帶的交貨技術條件
8 NF EN 10088-1-2005 不銹鋼 - 第1部分：不銹鋼清單
9 NF EN 10028-7-2008 壓力容器用不銹鋼扁平產品
10 NF EN 10028-7-2000 壓力容器用不銹鋼扁平產品
注：數據僅供參考价值！如有疑問吭芯，請?zhí)顚?我要糾錯"！
© 2024 材數庫
版權說明：
⑴ 本網站的所有內容（包括但不限于文字、圖片兰歼、音頻溪毕、視頻等）均受到版權保護，版權歸本網站所有廊擦；
⑵ 未經授權穿汽，禁止以任何形式轉載、復制觉浦、傳播或用于其他商業用途题束；
⑶ 如需使用本網站內容，請?zhí)崆矮@得授權院仿。