亚洲一区在线曰日韩下载,99亚洲国产精品精华液,亚洲欧洲国产综合aⅴ无码,欧美亚洲日韩国产系列

位置: 網站首頁 材料
牌號 X1CrNiMoCuN25-25-5
1.4537
對應標準 NF EN 10028-7-2000
壓力容器用不銹鋼扁平產品
Flat products made of steels for pressure purposes Part 7: Stainless steels
歸類 奧氏體不銹鋼
標簽 特殊等級
X1CrNiMoCuN25-25-5 化學元素成分含量(%)
成分 C Si Mn P S Cr Ni Cu Mo N
最小值 - - - - - 24 24 1 4.7 0.17
最大值 0.02 0.7 2 0.03 0.01 26 27 2 5.7 0.25
◎ 未經買方同意卫漫，不得隨意向鋼中添加表中未列的元素眷抠，冶煉精加工除外。采取一切必要措施以防在廢鋼和生產原料中帶入這些元素忽舟，因?yàn)槠鋾?huì)削弱鋼的機械性能随闺，降低鋼的適用性日川。
X1CrNiMoCuN25-25-5 機械性能
條件 熱處理或狀態
抗拉強度
σb
Mpa 		屈服點
σs
Mpa 		斷后伸長率或延伸率
δ
% 		沖擊吸收能量
KV2
J
P：T ≤ 75 +AT 600~800 Rp0.2：≥290
Rp1.0：≥330
①②		 T ＜ 3mm: ≥40
T ≥ 3mm: ≥ 40
②③		 20℃：
(l: ≥100；t: ≥60)
-196℃：
(t: ≥60)
◎C- 冷軋帶鋼; H- 熱軋帶鋼; P- 熱軋中厚板矩乐；T- 厚度龄句；t- 橫向；l-縱向恋猜。
◎+A=軟化退火畦洞；+AT=固溶退火；+QT=淬火及回火；+RA=再結晶退火铡捉。
◎ 如果熱加工和隨后冷卻的條件符合ENISO3651-2中對產品機械性能和抗晶間腐蝕性的要求战决，則可以省略固溶處理。
*抗晶間腐蝕根據EN ISO 3651-2進行測試劲徙。在交貨條件下：有窘燎；在致敏狀態下：有。
① 對于連續熱軋產品秘挥，可在詢價和訂購時商定Rp0.2(即表中σs)的最小值提高20MPa主瘸，Rp1.0的最小值提高10MPa。
② 如果在軋制寬度<300mm的帶材情況下兆焦，采用縱向試驗件糊怖，最小值減小如下:屈服強度-15MPa，恒定標距的延伸率-5%生碗，比例標距延伸率-2%捻艳。
③ T＜3mm：該值適用于標距為80mm、寬度為20mm的試件庆猫，也可以使用標距為50mm认轨、寬度為12.5mm的試件。T ≥3mm：該值適用于標距為5.65√S的試件月培。

  • 高溫下的最小屈服強度

    Material designationHeat treatment
    condition    		Minimum 0.2% proof strength Rp0.2,MPa
    at a temperature (in°C) of:
    Name Number100150200250300350400450500550600
    X1CrNiMoCuN25-25-51.4537+AT240220200190180175170----
    Minimum 1.0% proof strength Rp1.0,MPa
    at a temperature (in°C) of:
    100150200250300350400450500550600
    270250230220210205200----

  • 高溫下的最小抗拉強度

    Material designationMinimum tensile strength Rm,MPa
    at a temperature (in°C) of:
    Name Number100150200250300350400450500550600
    X1CrNiMoCuN25-25-51.4537550535520500480475-----

  • 熱處理指南

    Material designationHot formingHeat
    treatment
    symbol    		 Solution anneailing
    ①②    		Higher alloyed 
    austenitic
    steels with ≤ 0.02% C
    Name NumberTemperature
    ℃    		Type of
    cooling    		Temperature
    ℃ ③④    		Type of
    cooling    		Temperature
    ℃ ⑥    		Type of
    cooling
    X1CrNiMoCuN25-25-51.45371150 to 850air+AT1120 to 1180water,air ⑤not recommended- 
    ◎ a=air; o=oil; w=water.
    ◎ Scale and annealing colours produced during hot forming, heat treatment or welding may adversely affect the corrosion resistance. They should be removed as far as possible before use, e.g. by pickling.
    ◎ The temperatures of annealing should be agreed for simulated heat treated test pieces.
    ① The solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained and provided these requirements are met even after appropriate subsequent solution annealing.
    ② Re-crystallizing annealing.
    ③ If heat treatment is carried out in a continuous furnace, the upper part of the range specified is usually preferred, or even exceeded.
    ④ The lower end of the range specified for solution annealing should be aimed at for heat treatment as part of further processing,because otherwise the mechanical properties might be affected. If the temperature of hot forming does not drop below the lower temperature for solution annealing.a temperature of 980℃ is adequate as a lower limit for Mo-free steels,a temperature of 1000℃ for steels with Mo contents up to 3% and a temperature of 1020℃ for steets with Mo contents exceeding 3%.
    ⑤ cooling sufficiently rapid.

    ⑥ Minimum holding time:30min.

X1CrNiMoCuN25-25-5 對應不同標準
1 EN 10088-1-2005 不銹鋼 第1部分:不銹鋼的清單
2 EN 10088-3-2014 不銹鋼 - 第3部分：半成品嘁字，棒材，桿材杉畜，線材纪蜒，型材和光亮產品的一般用途耐腐蝕鋼的交貨技術條件
3 ISO 15510-2014 技術規范 不銹鋼-化學成分
4 ISO 9328-7-2018 不銹鋼承壓扁鋼制品
5 DIN EN 10088-3-2014 不銹鋼-半成品、棒材此叠、桿材纯续、線材、型材及光亮產品交貨技術條件
6 NF EN 10088-2-2005 普通用途不銹鋼板和鋼帶的交貨技術條件
7 NF EN 10088-1-2005 不銹鋼 - 第1部分：不銹鋼清單
8 NF EN 10028-7-2008 壓力容器用不銹鋼扁平產品
9 NF EN 10028-7-2000 壓力容器用不銹鋼扁平產品
注：數據僅供參考灭袁！如有疑問猬错，請?zhí)顚?我要糾錯"！
© 2024 材數庫
版權說明：
⑴ 本網站的所有內容（包括但不限于文字茸歧、圖片倦炒、音頻、視頻等）均受到版權保護晶会，版權歸本網站所有毁兼；
⑵ 未經授權，禁止以任何形式轉載暂韭、復制姿抒、傳播或用于其他商業用途奇门；
⑶ 如需使用本網站內容，請?zhí)崆矮@得授權茂蓬。